News
Contact Us
WEIFANG SHENGCHUAN MACHINERY CO.,LTD
Sales Director: Mr.Kevin Meng
Mob: +86 15692369696
Add: No.5999,Qingyuan street, Weifang, Shandong, China
Home > News > Content

Power Tiller Configuration Method

Weifang Shengchuan Machinery Co.,Ltd | Updated: Jul 06, 2017

power tiller Configuration method

Rotary tiller is a farming machine that works with tractors to complete tillage and rake operations. Because of its strong ability to break the soil, after the flat surface and other characteristics, and has been widely used. Proper use and adjustment of the rotary tiller, to maintain its good technical condition, to ensure the quality of farming is very important to rotating the tooth for the working parts of the drive-type soil farming machinery, according to the rotary knife axis configuration is divided into horizontal axis Type and vertical axis type.

Use edits

1. At the beginning of the operation, the rotary tiller should be lifted, first combined with the power output shaft, the tool shaft speed to the rated speed, and then down the rotary tiller, so that the blade gradually into the required depth. It is strictly prohibited to insert the blade into the power output shaft or drastically lower the rotary tiller to avoid causing the blade to bend or break and increase the load of the tractor. The same time as the above-

2. In the operation, should be as low as possible slow, so that can guarantee the quality of operations, so that the soil crushed, but also reduce the wear of parts. Pay attention to listen to the rotary tiller whether there is noise or metal percussion, and observe the broken soil, till the deep situation. If there is an abnormality, it should be immediately shut down for inspection, and then the operation can be continued. The same time as the above-

3. When the ground turns, prohibit the operation, the rotary tiller should be raised, so that the blade away from the ground, and reduce the tractor throttle, so as not to damage the blade. When lifting the rotary tiller, the inclination angle of the universal joint should be less than 30 degrees, and when it is too large, it will cause the impact noise to be prematurely worn or damaged. The same time as the above-

4. In the reverse, over the ridge and transfer the land, the rotary tiller should be raised to the highest position, and cut off the power, so as not to damage the parts. If you move to a distance, use a locking device to fix the rotary tiller. The same time as the above-

5. After each shift, the rotary tiller should be serviced. Remove the soil and weeds on the blade, check the fastening of the connectors, add lubricating oil to the lubricating oil, and add butter to the joints to prevent aggravating wear.

Adjust the editor

1. Horizontal adjustment. Will be with a rotary tiller drag the first stop in the flat ground, reduce the rotary tiller, so that the blade from the ground 5 cm, observe the left and right sides of the knife from the ground height is consistent to ensure that the work of the knife shaft level consistent farming deep uniform. The same time as the above-

2. Before and after the level of adjustment. When the rotary tiller is lowered to the desired depth, observe whether the angle of the universal joint is close to the horizontal position of the rotary tiller. If the universal joint angle is too large, you can adjust the upper rod, so that the rotary tiller in a horizontal position. The same time as the above-

3. Raise height adjustment. Rotation operation, the universal angle is not allowed to more than 10 degrees, when the ground is not allowed to turn more than 30 degrees. Therefore, the lifting of the rotary tiller, the use of bit adjustable screw can be used in the appropriate position of the handle limit; the use of height adjustment, the lifting of special attention, if you need to raise the rotary tiller, should cut the universal joint power The.


Contact Us
Weifang Shengchuan Machinery Co.,Ltd
Tel: 0086 0536-7599808
Address: No.5999 Qingyuan Street,ETDZ, Weifang, Shandong, China
Newsletter
Copyright © Weifang Shengchuan Machinery Co.,Ltd All rights reserved.
  • 0086-15692369696